Mostrar registro simples

dc.contributor.advisorSoares, Gabriel Vieira
dc.contributor.authorPerini, Felipe Gustavo
dc.date.accessioned2014-05-21T16:18:45Z
dc.date.available2014-05-21T16:18:45Z
dc.date.issued2014-05-21
dc.date.submitted2008-07-15
dc.identifier.urihttps://repositorio.ucs.br/handle/11338/315
dc.descriptionNa presente dissertação foram investigadas as propriedades mecânicas e microestruturais, antes e após o processo de soldagem, dos aços ZSTE380 e DOGAL800, que são aços de alta resistência e baixa liga (ARBL), além do aço convencional ZAR230. O principal objetivo do trabalho foi avaliar possíveis modificações nessas propriedades e verificar a possibilidade de substituir o aço convencional por um dos aços ARBL. Por serem mais resistentes os aços ARBL podem ser usados em elementos estruturais menos robustos, o que reduz o peso e a emissço de gases poluentes dos veículos. Primeiramente, verificaram-se diferentes extensões da zona termicamente afetada para os três aços soldados, onde é observada a maior extensão no DOGAL800 e a menor no ZAR230. A análise microestrutural revelou o crescimento do tamanho de grão austenítico em relação ao metal base nessa região para os aços ZSTE380 e DOGAL800, gerando um pronunciado aumento da resistência devido à transformação martensítica. O caso mais marcante ocorreu no DOGAL800, em cuja zona termicamente afetada observou-se a formação de martensita de baixo carbono, que é uma fase dura do aço, porém de baixa ductilidade. Os perfis de microdureza indicaram que não houve uma alteração significativa na dureza da zona termicamente afetada no ZAR230, enquanto que para o DOGAL800 observa-se um considerável aumento na mesma, confirmando a formaçao de martensita. Os limites de escoamento determinados pelos ensaios de tração não apresentaram diferenças significativas entre os corpos de prova com e sem solda se analisados de forma global, porém um ensaio de microtração, isso seria revelado. Contudo, nos ensaios de fadiga dos corpos de prova sem solda observou-se uma maior resistência à fadiga para os aços DOGAL800 e ZSTE380 em relação ao ZAR230. Após o processo de soldagem, os aços ARBL apresentam uma significativa redução da resistência a fadiga, estando abaixo da resistência à fadiga do ZAR230 para ensaios acima de um milhão de ciclos. Os resultados apresentados são explicados com base na relação entre as características microestruturais e propriedades mecânicas dos aços antes e após a soldagem.pt_BR
dc.description.abstractIn the present work we investigated the mechanical and microstructural proprieties of the ZSTE380 and DOGAL800 high strength low alloys steels (HSLA), comparing to the conventional ZAR230 steel, before and after welding. The main purpose is to detect possible modifications on these steels during the welding process, and to verify the possibility of replacing the conventional ZAR230 steel by one of the HSLAs. Since HSLA steels possess higher mechanical resistance, they can be used in less robust structures, which reduce the weight of the automobiles, and consequently reduce the emission of pollutant gases. We observed different extensions of the heat-affected zone for the three welded steels, with a higher extension in the DOGAL800 and the smaller extension in the ZAR230. Microstructural analysis revealed austenite grain growth in the heat-affected zone, in relation to the base metal in this region for the steels ZSTE380 and DOGAL800, becoming a remarkable increase of resistance due to martensite transformation. The most remarkable case happened in the DOGAL800, where we observed formation of low carbon martensite in the heat-affected zone, being this a harder phase of the steel, but with low ductility. The microhardness profiles indicated that it did not happen a significant change in hardness of the heat-affected zone of the ZAR230, while for the DOGAL800 it is observed a considerable increase in hardness, corroborating the hypothesis of martensite formation. The yield strength obtained form stress-strain curves didn?t revealed any significant differences between welded and without weld samples, if analyzed in a global way, but in a microtensile test, it would be reveled. The samples without weld submitted to the high-cycle fatigue test presented different fatigue resistance, where the DOGAL800 showed the greatest fatigue resistance, followed by the ZSTE380 and finally the ZAR230. However after the welding process we observed a significant reduction in the fatigue resistance of the HSLA steels, even below the ZAR230 resistance for tests above 1 million cycles. The results were explained relating the microstructure properties and the mechanical properties of the three steels, before and after welding.en
dc.language.isoptpt_BR
dc.subjectEngenharia de materiais e metalúrgicapt_BR
dc.subjectSoldagem de aços ARBL chapas finaspt_BR
dc.subjectZATpt_BR
dc.subjectpt_BR
dc.subjectAços de baixa ligapt_BR
dc.subjectSoldagempt_BR
dc.subjectSteel welding HSLA thin metal sheetpt_BR
dc.subjectHeat-affected zonept_BR
dc.subjectAçopt_BR
dc.titlePropriedades mecânicas e microestruturais de aços de alta resistência e baixa liga soldadospt_BR
dc.typeDissertaçãopt_BR
mtd2-br.advisor.instituationUniversidade de Caxias do Sulpt_BR
mtd2-br.advisor.latteshttp://lattes.cnpq.br/8082524565280979pt_BR
mtd2-br.author.lattesPERINI, F. G.pt_BR
mtd2-br.program.namePrograma de Pós-Graduação de Mestrado em Materiaispt_BR


Arquivos deste item

Thumbnail

Este item aparece na(s) seguinte(s) coleção(s)

Mostrar registro simples